Skip to content

Landing Gear Clearance on Taxiway Pavement: A Practical Guide

Planning aid only. Results must be verified by a qualified airport engineer against manufacturer data and applicable regulations.

Published 22 November 2026 (UTC).

Landing gear clearance on pavement is the gap between an aircraft's outer main-gear wheels and the edge of the taxiway or other paved surface. In FAA Advisory Circular 150/5300-13B (Airport Design), that gap is the taxiway edge safety margin, or TESM: the distance from the outer edge of the landing gear, with the nose gear on the taxiway centreline, to the edge of the taxiway pavement. ICAO Annex 14, Aerodromes, Volume I requires a minimum clearance between the outer main wheel and the taxiway edge, assuming the cockpit stays over the centreline marking.

Most jet transports steer from a nose gear well ahead of the main wheels. On a turn the inner main gear cut toward the inside of the curve, so a path that looks comfortable from the cockpit — or a straight taxiway that is wide enough — can still put a tyre closer to the edge than the design standard allows.

What taxiway edge safety margin means

On a straight taxiway the pavement has to hold the outer main-gear span plus the required edge margin on both sides. TESM is that margin in the FAA system. The circular sets a TESM for each Taxiway Design Group; larger groups have an equal or larger margin. Always read the figure from the current circular, not from memory or an old table.

ICAO Annex 14 requires a minimum clearance from the outer main wheel to the taxiway edge. That distance depends on the aeroplane's outer main gear wheel span, and on some curved taxiways it is larger for aeroplanes with a longer wheelbase. Use the edition that applies to the aerodrome.

The steering assumptions differ. FAA TESM is defined with the nose gear on the centreline; the ICAO rule assumes the cockpit remains over the centreline marking. Those stations are a short distance apart and produce slightly different main-gear paths in a turn, so a check should say which model it used. The margin is measured to the taxiway pavement edge, not automatically to the outer edge of a shoulder: a wheel that has left the taxiway edge is no longer inside the margin, even if it is still on a paved shoulder.

The two systems are not a unit conversion of each other. SteerSim can compare a simulated path against a selected standard; see Clearance standards.

Why the main gear cut the corner

A long vehicle making a 90-degree turn follows the curve with its front axle, while the rear axle takes a tighter path and cuts the corner. Aircraft do the same, because the wheelbase from nose gear to main gear is long, so the inner main-gear wheels pass closer to the inside curb or fillet than the nose gear did. A sharper turn, or a turn started closer to the inside, makes the cut-in worse.

The outer main gear, the nose, and the wingtips travel on different arcs: a steering choice that pulls the inner gear back toward the centreline pushes the nose and the outer wingtip farther outside. Gear-to-edge clearance and aircraft taxiing wingtip clearance have to be checked together. If either one is short, the movement is not safe to treat as a pass.

Cockpit-over-centreline and judgemental oversteer

The yellow taxiway centreline is a planning and driving aid, not a promise that every wheel stays a fixed distance from the edge. Two habits are common, and they are the two planning models in Swept-path modes:

  • Cockpit over the centreline. The pilots keep their station over the painted line. The cockpit sits aft of the nose gear, so the nose gear runs slightly outside the line in a turn and main-gear cut-in is usually a little less severe than nose-gear-on-centreline. This is the ICAO assumption for outer-main-wheel clearance.
  • Judgemental oversteer. The crew steers the nose farther outside so the main gear stay closer to the centreline. That can protect the inner gear and a tight fillet, but it is a judgement call, not a single published path, and it pushes the nose and the outer wingtip wider.

A third reference appears in the FAA definition of TESM: the nose gear on the centreline, close to but not the same as cockpit-over-centreline. Neither habit makes edge clearance automatic. A fillet designed around cockpit-over-centreline can look generous if every crew oversteers, and tight if someone tracks the line exactly. A layout that only works when crews oversteer is asking for a judgement call on every turn, including at night or in low visibility. Check more than one steering style.

Taxiway fillets and widened turns

Fillets add pavement at a taxiway intersection or curve so the inner main gear can still keep the required edge margin on a tight turn. Without that extra pavement, a centreline-following aircraft can put a tyre off the edge even when the straight taxiway was wide enough. ICAO taxiway-design material makes the same point: fillets at junctions and intersections protect wheel-to-edge clearance in a turn. Many designs also widen the taxiway on the approach to the turn, then provide a broader inside area through the curve. The painted centreline is the intended steering path; on a widened section it may not sit in the geometric middle of the pavement.

Fillets are sized to the aircraft the taxiway is meant to serve, and to the turn angle and radius. A 90-degree intersection that works for a short-wheelbase type may not work for a long-wheelbase aircraft in a more demanding Taxiway Design Group. Closely spaced turns are harder, because the aircraft may not be straight on the next centreline when the second turn begins.

SteerSim can sketch a fillet from the simulated inner-gear path of the selected aircraft; see Taxiway fillets. That sketch is a planning aid. Final fillet geometry still belongs with a qualified engineer and the current circular or Annex.

Taxiway shoulders

Taxiway shoulders sit outside the taxiway pavement edge. They typically limit erosion and jet blast, reduce debris, and can support an aircraft or vehicle that has already left the taxiway, but they are not a substitute for TESM. TESM and the ICAO wheel-to-edge clearance are measured to the taxiway pavement edge, so a wheel on the shoulder has already left that edge. Where the shoulder is paved in a similar colour to the taxiway, edge markings and lights show where the taxiway ends. Do not treat a shoulder as extra taxiway width unless the standard that applies says so.

Gear span versus wingspan

Gear track and wingspan drive different parts of the design.

  • ICAO. In the current Annex 14, Volume I, the aerodrome reference code letter (A to F) is based on wingspan. Taxiway width and the clearance from the outer main wheel to the taxiway edge are set from the aeroplane's outer main gear wheel span, which the Annex uses directly. Older editions used the more demanding of wingspan and outer main-gear wheel span to pick a single letter; current editions treat the two dimensions separately, so as not to over- or under-size the taxiway. Always use the edition that applies to the aerodrome.
  • FAA. AC 150/5300-13B, which superseded AC 150/5300-13A, uses two groupings. Airplane Design Groups I to VI are based on wingspan and tail height — the more demanding of those two decides the group — and are used for separations and object-free areas. Taxiway Design Groups are based on undercarriage geometry: main gear width, from outer edge to outer edge of the widest set of main-gear tyres, and cockpit-to-main-gear distance, from the pilot's eye to the main-gear turn centre. Taxiway width, TESM, and fillet standards follow the Taxiway Design Group, not the Airplane Design Group.

The critical aircraft for fillets may not be the critical aircraft for wingtip separation.

Stands and apron pavement

On the apron the "edge" is often a stand box, a lead-in, a service road, or an unpaved island. Stand entries are tight turns, and the lead-in is usually narrower than a taxiway, so the inner main gear can run out of pavement even when the apron looks large from above. Pushback and power-out follow a different path, so the gear tracks change and the tail and wingtips often swing through a new envelope. Mixed fleets add risk: a stand published for a smaller undercarriage may still be used by a type with a wider gear span or a longer wheelbase. Place the mix you actually expect, and check both the arrival and the departure, including the pavement edge along the lead-in. See Stands and aprons and Towing and pushback. For the wingtip half of the same problem, see Aircraft taxiing wingtip clearance.

How planners check a turn before construction

A fillet, stand entry, or taxiway widening is expensive to rebuild. A useful sequence is:

  1. Name the aircraft mix and the standard. Pick the critical types by gear track as well as by wingspan. Name the ICAO outer main gear wheel span and code letter, or the FAA Taxiway Design Group and Airplane Design Group, plus the edition you are using.
  2. Draw the path you expect people to follow. Use the real centreline, the planned fillet or widening, and the stand lead-in, not a typified 90-degree template that ignores the site.
  3. Simulate more than one steering style. Cockpit-over-centreline, nose-gear-on-centreline, and a deliberate oversteer case will not produce the same gear tracks.
  4. Look at the whole envelope. Inner and outer gear versus the pavement edges, both wingtips, and the tail, including the return movement or pushback. Treat a shoulder as a shoulder, not as extra taxiway, unless the standard says otherwise.
  5. Check pavement and objects that are not in the drawing yet. Temporary works, a closed fillet, and a service road painted to look like the taxiway are common real-world fouls.
  6. Record the assumption. A drawing that does not say which type, which standard, and which steering model was used is hard to defend later.

You can do a first pass in the browser before a survey or a detailed design model exists. Check a turn opens SteerSim's free taxi preview: an A350 arriving to a stand at Heathrow. From there you can read Pricing, or go back to the docs. This is a planning aid: a qualified airport engineer still has to verify the result against manufacturer data and the regulations that apply to that aerodrome.

Frequently asked questions

What is a taxiway edge safety margin?

In FAA AC 150/5300-13B, TESM is the distance from the outer edge of the landing gear, with the nose gear on the taxiway centreline, to the edge of the taxiway pavement. The circular sets a TESM for each Taxiway Design Group. Always read the current value from that circular, not from memory.

How does ICAO treat clearance from the outer main wheel to the taxiway edge?

ICAO Annex 14, Volume I requires a minimum clearance between the outer main wheel and the taxiway edge, assuming the cockpit stays over the centreline marking. The distance depends on outer main gear wheel span, and on some curves it is larger for a longer wheelbase. Use the edition that applies to the aerodrome.

Why do taxiway fillets exist?

On a turn the inner main gear cuts inside the path of the nose. Fillets and widened turns add pavement so those wheels can still keep the required edge margin. A straight taxiway that is wide enough does not, by itself, prove that a 90-degree intersection is wide enough.

What is the difference between cockpit-over-centreline and judgemental oversteer for gear clearance?

Cockpit-over-centreline puts the pilots' station on the painted line, which is the usual ICAO design assumption. Judgemental oversteer steers the nose farther outside so the main gear stay closer to the centreline. That can protect a tight fillet, but it is a judgement call and it pushes the nose and the outer wingtip wider. FAA TESM is defined with the nose gear on the centreline, a third, slightly different reference. A check should say which model it used.

How do ICAO and FAA use gear span and wingspan?

In the current ICAO Annex, the code letter is based on wingspan, while taxiway width and wheel-to-edge clearance are based on outer main gear wheel span. FAA Airplane Design Groups use wingspan and tail height; FAA Taxiway Design Groups use main-gear width and cockpit-to-main-gear distance, and that group sets TESM, taxiway width, and fillet standards. Always read the current Annex 14, Volume I or AC 150/5300-13B.

How can planners check landing-gear clearance on a tight turn?

Choose the critical aircraft by gear geometry as well as by wingspan, name the applicable standard, draw the real path and fillet, and inspect the swept gear tracks for more than one steering style. SteerSim's free preview is a starting point: Check a turn runs an A350-to-stand taxi at Heathrow. Final acceptance still belongs with a qualified engineer and the source documents.

Sources and further reading

Related SteerSim pages: Aircraft taxiing wingtip clearance, Clearance standards, Taxiway fillets, Swept-path modes, Stands and aprons, Methodology and limitations.