Skip to content

Aircraft Taxiing Wingtip Clearance: A Practical Guide

Planning aid only. Results must be verified by a qualified airport engineer against manufacturer data and applicable regulations.

Published 22 November 2026 (UTC).

Aircraft taxiing wingtip clearance is the space between an aircraft's wingtips — and its landing gear — and everything else on the airfield: other aircraft, stands, blast fences, lights, works areas, and the pavement edge. Most jet transports steer from a nose gear well ahead of the main wheels. On a turn those parts do not follow the same line, so a path that looks comfortable from the cockpit can still put a wingtip or a tyre closer to an object than the design standard allows.

This guide covers why wingtip and gear clearance is hard to judge by eye, how airport design standards group aircraft (mainly by wingspan), what changes on stands and in poor visibility, and how planners check a tight turn before construction.

Why wingtip clearance matters while taxiing

Ground collisions are usually slow, but they are expensive and they close stands and taxiways. A winglet or flap can be written off against a light pole or another aircraft's tail. Gear can leave the pavement on a fillet that is too tight.

Clearance is not only a "wingspan versus taxiway width" problem. Once an aircraft starts to turn, the wingtips, tail, and main gear travel on different arcs. On many swept-wing types the outer wingtip swings through a wider path than the parked wingspan suggests — often called swept-wing growth, or wing creep. SKYbrary's Wingtip Clearance Hazard is a useful operational briefing on that effect, and on why being on the centreline is not, by itself, a clearance guarantee.

The undercarriage is the other half of the problem. On a turn the inner main gear cuts toward the inside of the curve, while the outer main gear and outer wingtip swing wide. Designers therefore check two families of clearance at once: wingtip (and tail) to objects, other aircraft, and taxilane centrelines; and wheel to pavement edge, including fillets. If either one is short, the movement is not safe to treat as a pass. For the pavement-edge half of that problem, see Landing gear clearance on taxiway pavement.

Main-gear track and oversteer: why turns cut the corner

A long vehicle making a 90-degree turn follows the curve with its front axle, while the rear axle takes a tighter path and cuts the corner. Aircraft do the same, only more so: the wheelbase from nose gear to main gear is long, and the wings stick out far beyond the wheels. The inner main-gear wheels therefore pass closer to the inside curb or fillet than the nose gear did, and the outer wingtip — often with the tail — swings outside the path of the nose. A sharper turn, or a turn started closer to the inside, makes both effects worse.

Pilots sometimes use oversteer — steering the nose farther to the outside so the main gear stays closer to the taxiway centreline. That can protect the inner gear and the fillet, but it pushes the nose and the outer wingtip even wider. It is a trade, not a free improvement, and it is not a single published path. When you check a design, look at both a centreline-following case and a more aggressive oversteer case, then see where the wingtip and gear envelopes go.

For how SteerSim represents those two steering styles, see Swept-path modes.

Nose-gear steering and cockpit-over-centreline

The yellow taxiway centreline is a planning and driving aid, not a promise that every part of the aircraft stays a fixed distance from objects. Two habits are common:

  • Nose gear on the centreline. The steering axle tracks the painted line. The cockpit sits slightly off that line, and the main gear trails inside the turn.
  • Cockpit over the centreline. The pilots keep their own station over the line. Because the cockpit is aft of the nose gear on a tricycle transport aircraft, the nose gear runs slightly outside the line in a turn, and the main-gear cut-in is usually a little less severe. The outer wingtip path still needs a check.

Neither habit makes wingtip clearance automatic. On a long, swept wing the tip is a long way from the flight deck, often out of sight, and its path depends on the steering choice, the turn radius, and the aircraft geometry. A planner should say which steering model a drawing assumes. A design that only just works with one habit can fail if a crew uses the other, or if someone oversteers hard.

How design standards group aircraft by wingspan

Airport geometry is not sized to one famous aircraft type. Both of the widely used design systems put aeroplanes into size groups, then set taxiway and taxilane separations, object-free areas, and related clearances that grow as the group gets larger.

  • ICAO uses Aerodrome Reference Code letters A to F in Annex 14, Aerodromes, Volume I. In the current Annex the code letter is based on wingspan. Taxiway width and the clearance from the outer main wheel to the taxiway edge use the span of the outer main-gear wheels directly; see Landing gear clearance on taxiway pavement. Facilities planned for a given letter are meant to protect aircraft in that letter and the smaller ones, not automatically the letter above.
  • FAA uses Airplane Design Groups I to VI in Advisory Circular 150/5300-13A (Airport Design). That circular was later superseded by AC 150/5300-13B, the current FAA airport design circular. The groups are based on wingspan and tail height; the more demanding of those two dimensions decides the group. FAA also uses Taxiway Design Groups, which look at undercarriage geometry, for taxiway width and fillet design.

In both systems, as that group gets larger, the space between taxiway or taxilane centrelines, and the object-free area around those lines, is meant to grow with it. A taxiway that is comfortable for a mid-size narrow-body is not automatically comfortable for a wide-body in a larger group, even if the pavement is strong enough. The two systems are also not a unit conversion of each other.

Always open the current ICAO Annex, national specification, or FAA advisory circular that applies to the aerodrome, and use the values from that document — not a remembered number or a screenshot of an old table. SteerSim can compare a simulated path against a selected standard; see Clearance standards.

Stands and apron risks

The tightest wingtip problems are often on the apron, not out on a taxiway. Stands pack aircraft close together, so a nose-in stand has to protect wingtip clearance to a neighbouring aircraft and to objects on the stand; gear on the lead-in line and in the stand box; and the pushback or power-out, which is a different path from the arrival and often swings the tail and wingtips through a new envelope. Mixed fleets add risk: a stand published for a smaller group may still be used, in practice, by a larger type if the parking plan is not tightly controlled.

Taxilanes between stand rows are usually tighter than taxiways, so object-free area and wingtip-to-centreline checks matter more here than on a wide parallel taxiway. Temporary objects are a frequent surprise: a works area, a parked truck, a mobile stair, or equipment left in a closed stand. Place the aircraft mix you actually expect, and check both the arrival and the departure movement. See Stands and aprons and Towing and pushback.

Night and low visibility

The geometry does not change after dark, but the chance of noticing a tight margin does. Wingtips are already hard to see from the flight deck; at night, in rain, or in fog they are harder still. Centreline lights, stand lead-in lights, and painted marks become the main cues, and a faded mark or a confusing works area is easier to miss.

Low-visibility operations also change how the airfield is used. Aircraft hold longer, queue in unusual places, and may be asked to use a backup route. Notes that wingtip clearance is not assured exist for a reason: the painted line may keep the gear on the pavement and still not guarantee the wingtip against a known object or another aircraft on an adjacent line. For planners, the lesson is not to invent a different clearance number for night. It is to avoid designs that only work if everyone can see the wingtip, and to keep temporary obstacles out of the object-free area the standard is trying to protect.

How planners check a turn before construction

A fillet, a stand, or a taxiway widening is expensive to rebuild. A useful sequence is:

  1. Name the aircraft mix and the standard. Pick the critical types by wingspan and by gear track, and name the ICAO code letter or FAA design group, plus the edition of the document you are using.
  2. Draw the path you expect people to follow. Use the real centreline, the stand lead-in, and any planned fillet, not a typified 90-degree template that ignores the site.
  3. Simulate more than one steering style. Cockpit-over-centreline, nose-gear-on-centreline, and a deliberate oversteer case will not produce the same wingtip and gear tracks.
  4. Look at the whole envelope. Inner and outer gear versus the pavement edges, both wingtips, and the tail, including the return movement or pushback.
  5. Check objects that are not in the drawing yet. Temporary works, ground-service equipment, and aircraft on neighbouring stands are common real-world fouls.
  6. Record the assumption. A drawing that does not say which type, which standard, and which steering model was used is hard to defend later.

You can do a first pass in the browser before a survey or a detailed design model exists. Check a turn opens SteerSim's free taxi preview: an A350 arriving to a stand at Heathrow. From there you can read Pricing, or go back to the docs for the rest of the planner.

This is a planning aid. A qualified airport engineer still has to verify the result against manufacturer data and the regulations that apply to that aerodrome.

Frequently asked questions

Why does wingtip clearance matter while taxiing?

Because the wingtip, tail, and main gear do not follow the same line as the nose. A slow ground strike can still take an aircraft out of service and close a stand or taxiway. Staying on the centreline helps, but it does not by itself prove that the wingtip or the wheels are clear.

Why do the main gear cut the corner on a taxiway turn?

The main gear sit behind the steering axle. On a turn they take a tighter path than the nose gear, just as the rear wheels of a long vehicle cut inside the front path. That is why fillets exist, and why an inner-gear check against the pavement edge is as important as a wingtip check.

What is the difference between nose-gear and cockpit-over-centreline steering?

Nose-gear-on-centreline puts the steering axle on the painted line. Cockpit-over-centreline puts the pilots' station on the line, so the nose gear runs slightly outside the curve. The main-gear and wingtip paths change with that choice. A clearance check should say which model it used.

How do ICAO code letters and FAA design groups affect wingtip clearance?

ICAO Aerodrome Reference Code letters A to F are based on wingspan in the current Annex; taxiway width and wheel-to-edge clearance use outer main-gear wheel span. FAA Airplane Design Groups I to VI are based on wingspan and tail height. Taxiway and taxilane separations and object-free areas are then set to scale with that group. Always read the values from the current ICAO Annex 14, Volume I or FAA AC 150/5300-13B (which superseded AC 150/5300-13A), not from memory.

How can planners check a tight turn before construction?

Choose the critical aircraft and the applicable standard, draw the real path, and inspect the swept wingtip and gear tracks for more than one steering style. SteerSim's free preview is a starting point: Check a turn runs an A350-to-stand taxi at Heathrow. Final acceptance still belongs with a qualified engineer and the source documents.

Does night or low visibility change the clearance required?

The published design clearances do not shrink after dark. What changes is how much of the wingtip and the surrounding objects a crew can see. Layouts that only work with a perfect lookout are poor designs, and temporary objects should stay out of the protected area.

Sources and further reading

Related SteerSim pages: Landing gear clearance on taxiway pavement, Clearance standards, Swept-path modes, Stands and aprons, Methodology and limitations.